THIS PRODUCT IS FOR USE ON UNPOLISHED STONE AND MASONRY ONLY
NOT FOR USE ON POLISHED GRANITE
VOC COMPLIANT & LEGAL FOR USE IN ALL 50 STATES
Aqua Pro Impregnator provides state of the art protection for all unpolished stone, masonry, and grout in a cost effective and easy to use water-based formula. It is formulated with more impregnating solids to ensure maximum protection against water and oil-based stains that are particularly troublesome on porous surfaces that rapidly absorb spills of any kind.
Aqua Pro penetrates porous surfaces deeply to provide outstanding protection
against water and oil staining. It is gas permiable, allowing your
stones or masonry to properly "breathe" so that harmful moisture and by-products
are not trapped below the surface. It is non-yellowing and does not
change the surface appearance of your stone, masonry, or grout.
To keep your unpolished travertine, limestone, marble, or slate looking its best and to protect the surface between sealings, we
recommend Stone Pro Crystal Clean. For restoration-level cleaning of your unpolished stone or masonry prior to sealing with Aqua Pro, use Stone Pro Deep Clean Gel.
Coverage: Aqua Pro will cover approximately 1,000 ft.² per gallon dependant on the porosity of the stone. Two coats are recommended on new installations. 12 hrs. for water repellancy, 24 hrs for oil repellancy and full cure. Directions: Always test the product in an inconspicuous area to ensure suitability for intended use. Surface must be sound, thoroughly dry, and free from dirt, waxes, and old sealants or coatings of any kind. To remove topical sealers or waxes, use Stone Pro Formula 51 stripper before applying Aqua Pro. To remove heavy dirt or grime, use Stone Pro Deep Cleaning Gel. Apply a thin, even coat of Aqua Pro using a lambswool applicator or low-pressure sprayer and allow impregnator to remain on the surface for 10 minutes. If surface becomes dry during wait time, evenly apply a second thin coat. Do not dilute. After 10 minutes has elapsed, wipe ALL remaining Aqua Pro from the surface with a clean MicroFiber or white cotton cloth. DO NOT ALLOW AQUA PRO TO DRY ON THE SURFACE OF THE STONE - REMOVE ALL STANDING RESIDUE!
Manufacturer: Stone Pro 960 E. Discovery Lane, Anaheim, CA 92801
SECTION I - PRODUCT IDENTIFICATION
TRADE NAME: Stone Pro Aqua Pro PRODUCT CODE: AP
CHEMICAL NAME: Fluorochemical CAS #: N/A mixture
DOT HAZARD CLASS: N/A DATE: June 14, 2006
DOT SHIPPING NAME: Cleaning compound Non Hazardous
SECTION II - HAZARDOUS INGREDIENTS
HAZARDOUS INGREDIENTS CAS # % TLV (UNITS) PEL
Isopropyl Alcohol 67-63-0 <6 400 ppm 400 ppm
Ethylene Glycol Monobutyl Ether 111-76-2 <6 25 ppm skin 25 ppm
SECTION III - PHYSICAL DATA
BOILING POINT: (F) 212 SOLUBILITY: 100% pH: 7.8
PERCENT VOLATILE: ND VAPOR DENSITY: ND VAPOR PRESSURE: <30
EVAPORATION RATE (BUTYL ACETATE = 1): ND SPECIFIC GRAVITY: 1.00
APPEARANCE & ODOR: Clear liquid mild odor.
SECTION IV - FIRE AND EXPLOSION HAZARD INFORMATION
FLASH POINT: >250 degrees F.
FLAMMABLE LIMITS: N/A LOWER: N/A UPPER: N/A
FIRE/EXPLOSION HAZARDS: None
EXTINGUISHING MEDIA: Foam, CO2, dry chemical
FIRE FIGHTING PROCEDURES: Fire fighters should wear self-contained breathing apparatus and full protective clothing. Use water spray to cool nearby containers and structures exposed to fire.
SECTION V - HEALTH HAZARD INFORMATION
PERMISSIBLE EXPOSURE LEVEL: ND
EYES: Slight irritation
SKIN: None under normal conditions.
INHALATION: None under normal conditions.
INGESTION: Ingesting large quantities may cause nausea.
THIS MATERIAL IS NOT LISTED AS A CARCINOGEN BY IARC, NTP OR OSHA
HMIS HAZARD CLASS: Health = 0 Flammability = 0 Reactivity =0 Other =NA
Ranking: 0 = Least 1 = Slight 2 = Moderate 3 = High 4 = Extreme
FIRST AID
EYE CONTACT: Flush with water for 20 minutes lifting eyelids. Get medical attention immediately
SKIN CONTACT: Immediately flush skin with water for 20 minutes. Remove and launder contaminated clothing before use.
INHALATION: Remove victim to fresh air. Administer artificial respiration if breathing ceases. Get medical attention immediately.
INGESTION: Do not induce vomiting. Give lots of water, if conscious. Get medical attention immediately.
SECTION VI - REACTIVITY INFORMATION
STABILITY: Stable
REACTIVITY: None will occur
HAZARDOUS DECOMPOSITION INGREDIENTS: As with any organic material, CO AND CO2 may be expected as by-products of combustion.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION VII - SPILL, LEAK AND DISPOSAL PROCEDURES
SMALL SPILLS: Absorb with an inert material such as sand or Vermiculite and sweep up and dispose of in accordance with federal, state, and local regulations.
LARGE SPILLS: Absorb with and inert material such as sand or Vermiculite and sweep up and dispose of in accordance with federal, state, and local regulations.
DISPOSAL: Dispose of in accordance with federal, state, and local regulations.
SECTION VIII - SPECIAL PROTECTIVE EQUIPMENT
EYE AND FACIAL: None required under normal conditions.
SKIN: None required under normal conditions.
RESPIRATORY: None required under normal conditions.
VENTILATION: Local mechanical ventilation to keep TLV’S below recommended levels.
OTHER: None required under normal conditions.
SECTION IX - SPECIAL PRECAUTIONS
STORAGE: Store in cool, dry, well-ventilated place.
HANDLING: No special needs.
LEGEND: ND, Not Determined; N/A Not Applicable; NA, Not Available.
NOTICE
All information appearing herein is based upon data obtained from chemical manufacturers and or recognized technical sources. While the information is believed to be accurate, Snyder Manufacturing Corporation makes no representations as to its accuracy or sufficiency. Conditions of use are beyond Snyder Manufacturing Corporation’s control and therefore users are responsible for and assume all risks of their use, handling, and disposal of the product, or from the publication or use of, or reliance upon, information contained herein. This information relates only to the product designated herein, and does not relate to its use in combination with any other material or in any other process
|
