THIS PRODUCT IS FOR USE ON UNPOLISHED STONE AND MASONRY ONLY
NOT FOR USE ON GRANITE
VOC COMPLIANT & LEGAL FOR USE IN ALL 50 STATES
"Porous Pro" provides state of the art protection for all unpolished stone, masonry, and grout. It is formulated with more impregnating solids to ensure maximum protection against water and oil-based stains that are particularly troublesome on porous surfaces that rapidly absorb spills of any kind.
Porous Pro penetrates porous surfaces deeply to provide unsurpassed protection
against water and oil staining. It is gas permiable, allowing your
stones or masonry to properly "breathe" so that harmful moisture and by-products
are not trapped below the surface. It is non-yellowing and does not
change the surface appearance of your stone, masonry, or grout.
We
always recommend a solvent-based impregnator on natural stones
because solvents penetrate dense surfaces better than water
carriers and deliver the impregnating solids (the part that actually
protects your stone) deeper into the surface.
To keep your unpolished travertine, limestone, marble, or slate looking its best and to protect the surface between sealings, we
recommend Stone Pro Crystal Clean. For restoration-level cleaning of your unpolished stone or masonry prior to sealing with Porous Pro, use Stone Pro Deep Clean Gel.
Coverage: Porous Pro will cover approximately 250 ft.� per quart dependant on the porosity of the stone. Two coats are recommended on new installations. 2 hrs. for water repellancy, 4 hrs for oil repellancy and full cure.
Directions: Always test the product in an inconspicuous area to ensure suitability for intended use. Surface must be sound, thoroughly dry, and free from dirt, waxes, and old sealants or coatings of any kind. To remove topical sealers or waxes, use Stone Pro Formula 51 stripper before applying Porus Pro. To remove heavy dirt or grime, use Stone Pro Deep Cleaning Gel. Apply a thin, even coat of Porous Pro using a solvent-resistant applicator or low-pressure sprayer and allow impregnator to remain on the surface for 7-10 minutes. If surface becomes dry during wait time, evenly apply a second thin coat. Do not dilute. After 7-10 minutes has elapsed, wipe ALL remaining Porous Pro from the surface with a clean MicroFiber or white cotton cloth. DO NOT ALLOW POROUS PRO TO DRY ON THE SURFACE OF THE STONE - REMOVE ALL STANDING RESIDUE!
SECTION I -COMPANY &PRODUCT IDENTIFICATION
TRADE NAME:Stone Pro Porous Pro Sealer
PRODUCT CODE:N/A
CHEMICAL NAME:Fluoropolymer emulsion CAS #:Mixture,no single CAS #applies
DATE:June 26,2006
SECTION II -COMPOSITION FORMULA -HAZARDOUS INGREDIENTS
HAZARDOUS INGREDIENTS %CAS #TLV (UNITS)PEL
Isopropyl Alcohol <6 67-63-0 400 ppm 400 ppm
Ethylene Glycol Monobutyl Ether <6 111-76-2 25 ppm skin 25 ppm
SECTION III -HAZARDS IDENTIFICATION
PERMISSIBLE EXPOSURE LEVEL:Undetermined
EYES:May cause mild eye irritation.
SKIN:May cause mild skin irritation.
INHALATION:Breathing small amounts of this material during normal handling is not likely to cause harmful effects.
INGESTION:Swallowing this material may be harmful
THIS MATERIAL IS NOT LISTED AS A CARCINOGEN BY IARC,NTP OR OSHA
SECTION IV -FIRST AID MEASURES
EYE CONTACT:Flush with water for 15 minutes lifting eyelids.Get medical attention if necessary.
SKIN CONTACT:Wash with soap and water.
INHALATION:Remove victim to fresh air.Administer arti ficial respiration if breathing ceases.Get medical attention
immediately.
INGESTION:Do not induce vomiting.Call physician or transport to an emergency medical facility.
SECTION V -FIRE AND EXPLOSION HAZARD INFORMATION
FLASH POINT:195 deg.F.
EXPLOSIVE LIMITS:LOWER:N/D UPPER:N/D
FIRE/EXPLOSION HAZARDS:None.
EXTINGUISHING MEDIA:Foam,CO2,dry chemical
FIRE FIGHTING PROCEDURES:Fire fighters should wear self-contained breathing apparatus with a full-face piece
operated in the positive pressure demand mode and full protective clothing.Use water spray to cool nearby con-
tainers and structures.
HMIS HAZARD CLASS:Health =1 Flammability =1 Reactivity =0 Other =NA
Ranking:0 =Least 1 =Slight 2 =Moderate 3 =High 4 =Extreme
SECTION VI -ACCIDENTAL RELEASE PROCEDURES
SMALL SPILLS:Absorb liquid on vermiculite,floor absorbent or other absorbent material.
LARGE SPILLS:Eliminate all ignition sources.Prevent run off to drains or any bodies of water.Pump or vacuum ma-
terial to containers for recovery.Absorb remaining material.
SECTION VII -HANDLING &STORAGE
STORAGE:Keep cool and dry.Empty containers may contain fumes.All hazard precautions on this data sheet
should be taken when handling empty containers.
HANDLING:Sudden release of hot organic chemical vapors may result in ignition without the presence of obvious
ignition sources.
SECTION VIII -EXPOSURE CONTROL/PERSONAL PROTECTION
Wear chemical splash goggles.
SKIN:None required under normal conditions.
RESPIRATORY:None required under normal conditions.
VENTILATION:Normal ventilation acceptable under normal conditions.
SECTION IX -PHYSICAL AND CHEMICAL PROPERTIES
BOILING POINT:F 200 SOLUBILITY:Soluble pH:No data
PERCENT VOLATILE:<10%,100 gms/l VAPOR DENSITY:N/D VAPOR PRESSURE:N/D
EVAPORATION RATE (BUTYL ACETATE=1):151 (Ether)SPECIFIC GRAVITY:..98 @60 deg F.
APPEARANCE &ODOR:Clear liquid with solvent odor.
SECTION X -STABILITY &REACTIVITY INFORMATION
HAZARDOUS DECOMPOSITION INGREDIENTS:CO2,CO,and phosphorous compounds.
HAZARDOUS POLYMERIZATION:Will not occur
SECTION XI -TOXICOLOGICAL INFORMATION
No toxicological information has been generated for this material.
SECTION XII -ECOLOGICAL INFORMATION
This product has never been found to present any environmental or ecological problems. Use according to the
instructions. Dispose of in a sanitary manner.
SECTION XIII -DISPOSAL CONSIDERATION
Dispose in accordance with federal,state and local regulations.
SECTION XIV -TRANSPORT INFORMATION
DOT INFORMATION-49CFR 172.101:
DOT DESCRIPTION:None required
SECTION XV -REGULATORY INFORMATION
TSCA � Intentional ingredients are listed;;CERCLA RQ-40CFR 302.4 (a)� None listed;;SARA 302 Components 40 CFR
355 Appendix A � None;;Section 311/312 Hazard Class-40CFR 370.2 � Immediate ((X)Delayed ()Fire (X)Reac-
tive ()Sudden release of pressure ();SARA 313 Components 40CFR 372.65 � None;;OSHA Process Safety Manage-
ment 29CFR1910 � None listed;;EPA Accidental Release Prevention 40CFR68 � None listed..
International Regulations:
ACOIN (Australia),DSL (Canada),ECL (South Korea),&EINECS (Europe)� Intentional ingredients are listed..
State &Local Regulations:
California Prop 65 � None
|
Porous Pro 
