Stone Pro Crystal Clean is a highly concentrated, neutral cleaner and protector for marble, granite, travertine, limestone, slate, all other natural stone, ceramic tile, porcelain tile, and grout. This is the single-most important product you can use to keep your stone and tile surfaces in top condition, and should be the cornerstone of your routine cleaning practices.Crystal Clean is strong enough for commercial use, yet safe for the
home. Its powerful cleaning agents are highly effective on dirt and
grime, and it leaves an invisible, streak-free protective shield against
soil and staining. Crystal Clean does not contain acids or alkalines that can damage your stone, or chelates that can leave your surfaces looking dull and lifeless. It is a perfect �7 pH neutral cleaner that will not damage or change the appearance of your surfaces, even with daily use. Crystal Clean contains two evaporating agents that make it dry three times faster than plain water or other stone cleaners. When used with the damp mopping technique, Crystal Clean will drastically reduce water induced fill loss and spalling in travertine, limestone, and marble, and microbial growth in pits and grout lines. Crystal Clean contains a small amount ofthe same fluoropolymer impregnator found in the Stone Pro family of sealers. Every time you use Crystal Clean on your stone or tile surfaces, you are strengthening their ability to resist water penetration and staining from both water and oil-based substances, and retarding the growth of mold and bacteria that cause discoloration in surface pits and grout lines.
Crystal Clean is both highly concentrated and economical to use. One gallon creates up to 16 gallons of cleaning solution that can be used on all your natural stone and tile surfaces. At normal concentration levels, this is enough product to clean 500 square feet of stone or tile, once a week, for four months.
If you have the need to clean travertine, clean marble, clean granite, clean limestone, or clean tile, Stone Pro Crystal Clean is your best choice!
For Use on Floors and Larger Surface Areas
Dilute Crystal Clean Per the following instructions:
Light / Medium Soiling - 1 Part Crystal Clean to 16 Parts Water (1 Cup to 1 Gallon)
Medium Soiling or Polished Surfaces - 1 Part Crystal Clean to 8 Parts Water (2 Cups to 1 Gallon)
Heavy Soiling (Non-Staining) - 1 Part Crystal Clean to 4 Parts Water (4 Cups to 1 Gallon)
Before applying any moisture to your flooring, always ensure all dust, dirt, and other dry contaminates are completely removed from the surface. This may be accomplished by sweeping or using the vacuum. This is important for two reasons:
- Dust, dirt, and other dry contaminates mix with the cleaning solution and become deposited in the grout lines.
- Dry surface contaminates have an abrasive effect on the floor surface, and over time will degrade the finish.
Please be careful if using a vacuum cleaner as the wheels or attachments may scratch the surface.
After removing dry surface contaminates as described above, the floor should be damp moped
using the sponge mop. The object of the process is to keep as much standing cleaning solution
as possible off the floor and out of the grout lines.
Damp moping instructions are as follows:
A. Ensure you have removed all dry surface contaminates, as described above.
B. Mix Crystal Clean Concentrate with cold tap water per the recommended dilution rate, above.
C. Dip the mop head into the Crystal Clean mixture and wring it completely out.
D. Damp mop a section of the floor or surface area and check the mop head for dirt.
E. When the mop head is dirty, rinse it in clean water. NOTE: DO NOT RINSE THE CRYSTAL CLEAN SOLUTION
FROM THE FLOOR! YOU WILL VOID ALL THE BENEFITS OF USING IT.
F. Repeat Items C-E until complete.
For Use as A Spray Cleaner for Counters, Showers, Etc.
Add 6 Ounces of Crystal Clean Concentrate to an empty 1 quart spray bottle, and fill with cool tap water. Shake to mix. Spray the surface to be cleaned, then wipe with a clean, soft cloth. Do not rinse!
SECTION I - PRODUCT IDENTIFICATION
TRADE NAME: Crystal Clean PRODUCT CODE: CC
CHEMICAL NAME: Detergent CAS #: N/A mixture DOT HAZARD CLASS: N/A DATE: October 9, 2004
DOT SHIPPING NAME: Cleaning compound Non Hazardous
SECTION II - HAZARDOUS INGREDIENTS
HAZARDOUS INGREDIENTS CAS # TLV (UNITS) PEL
The ingredients in this product are generally recognized as non-hazardous, non-toxic, and non-restricted.
SECTION III - PHYSICAL DATA
BOILING POINT: (F) 212 SOLUBILITY: 90% pH: 7.8
PERCENT VOLATILE: ND VAPOR DENSITY: ND VAPOR PRESSURE: <30
EVAPORATION RATE (BUTYL ACETATE = 1): ND SPECIFIC GRAVITY: 1.00
APPEARANCE & ODOR: Light blue clear liquid mild odor.
SECTION IV - FIRE AND EXPLOSION HAZARD INFORMATION
FLASH POINT: N/A
FLAMMABLE LIMITS: N/A LOWER: N/A UPPER: N/A
FIRE/EXPLOSION HAZARDS: None
EXTINGUISHING MEDIA: Foam, CO2, dry chemical
FIRE FIGHTING PROCEDURES: Fire fighters should wear self-contained breathing apparatus and full protective clothing. Use water spray to cool nearby containers and structures exposed to fire.
SECTION V - HEALTH HAZARD INFORMATION
PERMISSIBLE EXPOSURE LEVEL: ND
EYES: Slight irritation
SKIN: None under normal conditions.
INHALATION: None under normal conditions.
INGESTION: Ingesting large quantities may cause nausea.
THIS MATERIAL IS NOT LISTED AS A CARCINOGEN BY IARC, NTP OR OSHA
HMIS HAZARD CLASS: Health = 0 Flammability = 0 Reactivity =0 Other =NA
Ranking: 0 = Least 1 = Slight 2 = Moderate 3 = High 4 = Extreme
FIRST AID
EYE CONTACT: Flush with water for 20 minutes lifting eyelids. Get medical attention immediately
SKIN CONTACT: Immediately flush skin with water for 20 minutes. Remove and launder contaminated clothing before use.
INHALATION: Remove victim to fresh air. Administer artificial respiration if breathing ceases. Get medical attention immediately.
INGESTION: Do not induce vomiting. Give lots of water, if conscious. Get medical attention immediately.
SECTION VI - REACTIVITY INFORMATION
STABILITY: Stable
REACTIVITY: None will occur
HAZARDOUS DECOMPOSITION INGREDIENTS: As with any organic material, CO AND CO2 may be expected as by-products of combustion.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION VII - SPILL, LEAK AND DISPOSAL PROCEDURES
SMALL SPILLS: Absorb with an inert material such as sand or Vermiculite and sweep up and dispose of in accordance with federal, state, and local regulations.
LARGE SPILLS: Absorb with and inert material such as sand or Vermiculite and sweep up and dispose of in accordance with federal, state, and local regulations.
DISPOSAL: Dispose of in accordance with federal, state, and local regulations.
SECTION VIII - SPECIAL PROTECTIVE EQUIPMENT
EYE AND FACIAL: None required under normal conditions.
SKIN: None required under normal conditions.
RESPIRATORY: None required under normal conditions.
VENTILATION: Local mechanical ventilation to keep TLVʼS below recommended levels.
OTHER: None required under normal conditions.
SECTION IX - SPECIAL PRECAUTIONS
STORAGE: Store in cool, dry, well-ventilated place.
HANDLING: No special needs.
LEGEND: ND, Not Determined; N/A Not Applicable; NA, Not Available.
NOTICE
All information appearing herein is based upon data obtained from chemical manufacturers and or recognized technical sources. While the information is believed to be accurate, Snyder Manufacturing Corporation makes no representations as to its accuracy or sufficiency. Conditions of use are beyond Snyder Manufacturing Corporationʼs control and therefore users are responsible for and assume all risks of their use, handling, and disposal of the product, or from the publication or use of, or reliance upon, information contained herein. This information relates only to the product designated herein, and does not relate to its use in combination with any other material or in any other process
|
Stone Pro Crystal Clean 
