Stone Pro Deep Clean Gel is unique cleaning formulation designed to remove grease, grime, soap scum, hard water spots, and other stubborn soils and stains from natural stone surfaces. It is for use on all polished, honed, flamed and tumbled marble, granite, limestone, travertine, slate, other natural stones, terrazzo, tile, and associated grout lines. Deep Clean Gel is non-acidic, and does a terrific job on both sanded and non-sanded grouts.
Deep Clean Gel can also be used to neutralize acidic polishing powder residue from products such as Stone Pro 5X, Diamond Renew, and Oxcilic Acid, as well as acid-based grout cleaners such as Stone Pro Quick Clean.
If you are unable to remove a stain after using Deep Clean Gel, this means the stain is embedded in the stone's surface and will require the use of a poultice. To view our Poultice Stain Remover, please check the "Accessories" Section to the right.
Caution: Alkaline cleaning properties, dangerous if swallowed. May cause skin irritation on contact. The use of safety equipment is suggested. Chemical resistant gloves and eye protection should be worn at all times when using this product.Stone Pro and Terra BioCleans' liability, either expressed or implied, is limited solely to the replacement of this product when proven to be defective, and does not include any labor costs or consequential damages. It is the user's responsibility to determine the safety, toxicity, and suitability of this product. Person(s) testing for desired results and effects to determine suitability of this product for any intended or unintended purpose shall be solely responsible for any outcome related to the use of this product.
Coverage: Product will cover approximately 200 to 2,000 ft.˛ per gallon dependant on the severity of surface soiling. For stone grout joints which have been heavily soiled, use at 2:1 ratio with cold tap water. Dilution rate may slightly reduce cleaning effectiveness. Light duty areas may be diluted up to 12:1. As a neutralized for acidic powder polishes or acid-based grout cleaners, mix 8 oz. of Deep Clean Gel with 1 gallon of cold tap water. Directions: Always apply this product to an inconspicuous area to test suitability for intended use. Apply properly diluted Deep Clean Gel to the designated area. - For small areas, wipe, scrub and/or agitate the product into surface using light duty, non-abrasive hand scrubber.
- For floors, apply product to designated areas and use a tampico brush to agitate and scrub floor liberally.
- Let Deep Clean Gel dwell for approximately 5 to 10 minutes, depending on the severity of the soiling. Dwell time allows synthetic surfactants to release dirt and move it to the surface.
- Wipe or wet-vacuum residue from the surface.
- Rinse thuroughly with cold water and wipe or wet-vacuum rinse water from surface.
- For porous stone or tiles, remove the product with a wet-vacuum to completely remove soil from crevices.
SECTION I - PRODUCT IDENTIFICATION
TRADE NAME: Stone Pro Deep Clean Gel PRODUCT CODE: SPDCG
CHEMICAL NAME: Alkaline cleaner CAS #: Blend, no single CAS # applies DOT HAZARD CLASS: Not regulated DATE: February 19, 2005
DOT SHIPPING NAME: Not regulated
SECTION II - HAZARDOUS INGREDIENTS
HAZARDOUS INGREDIENTS % CAS # TLV (UNITS) PEL
2(butyoxyethoxy) Ethanol <5 112345 None None
Sodium Metasilicate <5 6834-92-0 15 mg/m3 10 mg/m3
SECTION III - PHYSICAL DATA
BOILING POINT: (F) 212 SOLUBILITY: Complete pH: 13
VOC: 20.8 g/L VAPOR DENSITY: N/A VAPOR PRESSURE: N/A
EVAPORATION RATE (WATER = 1); >1 SPECIFIC GRAVITY: 1.04
APPEARANCE & ODOR: Yellow liquid with lemon odor.
SECTION IV - FIRE AND EXPLOSION HAZARD INFORMATION
FLASH POINT: N/A
FLAMMABLE LIMITS: N/A LOWER: N/A UPPER: N/A
FIRE/EXPLOSION HAZARDS: None
EXTINGUISHING MEDIA: Foam, CO2, dry chemical
FIRE FIGHTING PROCEDURES: Fire fighters should wear self-contained breathing apparatus and full protective clothing. Use water spray to cool nearby containers and structures exposed to fire.
SECTION V - HEALTH HAZARD INFORMATION
PERMISSIBLE EXPOSURE LEVEL: ND
EYES: Will cause irritation and redness.
SKIN: Prolonged contact will cause irritation and redness.
INHALATION: Prolonged inhalation of mist will cause nasal and respiratory irritation.
INGESTION: Can cause gastrointestinal irritation, nausea, vomiting or diarrhea.
THIS MATERIAL IS NOT LISTED AS A CARCINOGEN BY IARC, NTP OR OSHA
HMIS HAZARD CLASS: Health = 1 Flammability = 0 Reactivity = 0 Other =NA
Ranking: 0 = Least 1 = Slight 2 = Moderate 3 = High 4 = Extreme
FIRST AID
EYE CONTACT: Flush with water for 15 minutes lifting eyelids. Get medical attention immediately
SKIN CONTACT: Wash with water and treat with any moisturizing cream.
INHALATION: Remove victim to fresh air. Administer artificial respiration if breathing ceases. Get medical attention immediately.
INGESTION: Do not induce vomiting. Give lots of water. Give milk of magnesia. Call a physician.
SECTION VI - REACTIVITY INFORMATION
STABILITY: Stable
REACTIVITY: None will occur
HAZARDOUS DECOMPOSITION INGREDIENTS: N/A
HAZARDOUS POLYMERIZATION: Will not occur
SECTION VII - SPILL, LEAK AND DISPOSAL PROCEDURES
SMALL SPILLS: Mop, sweep or absorb. Transport to non-hazardous land fill.
LARGE SPILLS: Mop, sweep, or absorb. Transport to non-hazardous land fill.
DISPOSAL: Dispose of in accordance with federal, state, and local regulations.
SECTION VIII - SPECIAL PROTECTIVE EQUIPMENT
EYE AND FACIAL: Wear chemical splash goggles.
SKIN: Vinyl, rubber, or nitrile gloves should be used.
RESPIRATORY: Provide OSHA approved mists respirator.
VENTILATION: Local mechanical ventilation to keep TLVʼS below recommended levels.
OTHER: Wear protective apron, boots, and clothing.
SECTION IX - SPECIAL PRECAUTIONS
STORAGE: Store in cool dry well ventilated place
HANDLING: Avoid strong mineral acids.
LEGEND: ND, Not Determined; N/A Not Applicable; NA, Not Available.
NOTICE
All information appearing herein is based upon data obtained from chemical manufacturers and or recognized technical sources. While the information is believed to be accurate, Snyder Manufacturing Corporation
makes no representations as to its accuracy or sufficiency. Conditions of use are beyond Snyder Manufacturing Corporationʼs control and therefore users are responsible for and assume all risks of their use, handling,
and disposal of the product, or from the publication or use of, or reliance upon, information contained herein. This information relates only to the product designated herein, and does not relate to its use in combination
with any other material or in any other process.
|
Brought the marble back to life! 
