Test in an inconspicuous area to confirm suitability for intended use.

Lightly spray the area you wish to clean and polish.  Using a clean MicroFiber towel or clean cloth, wipe the area until the product is completely removed from the surface.

Take a dry section of your clean Microfiber towel or clean cloth and buff to a high gloss shine.

Repeat as often as necessary - Finishing Touch is safe for daily, weekly, or monthly use!

SECTION I - COMPANY & PRODUCT IDENTIFICATION
TRADE NAME: Stone Pro Finishing Touch PRODUCT CODE: N/A
CHEMICAL NAME: Silane emulsion CAS #: Mixture, no single CAS # applies
DATE: September 5, 2003

SECTION II - COMPOSITION FORMULA - HAZARDOUS INGREDIENTS
HAZARDOUS INGREDIENTS CAS # TLV (UNITS) PEL
Hydrocarbon propellant 68476-86-8 800 PPM 800 PPM

SECTION III - HAZARDS IDENTIFICATION
PERMISSIBLE EXPOSURE LEVEL: Undetermined
EYES: May cause mild eye irritation.
SKIN: Normal handling should not present any problems.
INHALATION: Breathing small amounts of this material during normal handling is not likely to cause harmful effects.
INGESTION: Swallowing small amounts of this material during normal handling is not likely to cause harmful effects.
THIS MATERIAL IS NOT LISTED AS A CARCINOGEN BY IARC, NTP OR OSHA

SECTION IV - FIRST AID MEASURES
EYE CONTACT: Flush with water for 15 minutes lifting eyelids. Get medical attention.
SKIN CONTACT: Flush skin with water for 15 minutes. Remove and launder contaminated clothing before use.
INHALATION: Remove victim to fresh air. Administer artificial respiration if breathing ceases. Get medical attention immediately.
INGESTION: Do not induce vomiting. Call physician or transport to an emergency medical facility.

SECTION V - FIRE AND EXPLOSION HAZARD INFORMATION
FLASH POINT: Level 1 Aerosol.
EXPLOSIVE LIMITS: LOWER: N/A UPPER: N/A
FIRE/EXPLOSION HAZARDS: Keep containers cool.
EXTINGUISHING MEDIA: Foam, CO2, dry chemical
FIRE FIGHTING PROCEDURES: Fire fighters should wear self-contained breathing apparatus with a full-face piece operated in the positive pressure demand mode and full protective clothing. Use water spray to
cool nearby containers and structures.
HMIS HAZARD CLASS: Health =0 Flammability =0 Reactivity =0 Other =NA
Ranking: 0 = Least 1 = Slight 2 = Moderate 3 = High 4 = Extreme

SECTION VI - ACCIDENTAL RELEASE PROCEDURES
SMALL SPILLS: Absorb liquid on vermiculite, floor absorbent or other absorbent material.
LARGE SPILLS: Eliminate all ignition sources. Prevent run off to drains or any bodies of water. Pump or vacuum material to containers for recovery. Absorb remaining material.

SECTION VII - HANDLING & STORAGE
STORAGE: Keep cool and dry. Empty containers may contain fumes. All hazard precautions on this data sheet should be taken when handling empty containers.
HANDLING: Sudden release of hot organic chemical vapors may result in ignition without the presence of obvious ignition sources.

SECTION VIII - EXPOSURE CONTROL/PERSONAL PROTECTION
EYE AND FACIAL: Wear safety glasses.
SKIN: No protection necessary under normal conditions.
RESPIRATORY: No protection necessary under normal conditions.
VENTILATION: Local mechanical ventilation to keep TLVʼS and PEL below recommended levels

SECTION IX - PHYSICAL AND CHEMICAL PROPERTIES
BOILING POINT: N/A SOLUBILITY: Complete pH: 7.5
PERCENT VOLATILE: 0 VAPOR DENSITY: N/A VAPOR PRESSURE: .N/A
EVAPORATION RATE (BUTYL ACETATE=1): >5 SPECIFIC GRAVITY: 1.0 @60 deg F.
APPEARANCE & ODOR: Foamy aerosol spray. VOC: 0

SECTION X - STABILITY & REACTIVITY INFORMATION
STABILITY: Stable
REACTIVITY: N/A
HAZARDOUS DECOMPOSITION INGREDIENTS: CO2, CO, and phosphorous compounds.
HAZARDOUS POLYMERIZATION: Will not occur

SECTION XI - TOXICOLOGICAL INFORMATION
No toxicological information has been generated for this material

SECTION XII - ECOLOGICAL INFORMATION
This product has never been found to present any environmental or ecological problems. Use according to the instructions. Dispose of in a sanitary manner.

SECTION XIII - DISPOSAL CONSIDERATION
Dispose in accordance with federal, state and local regulations.

SECTION XIV - TRANSPORT INFORMATION
DOT INFORMATION- 49CFR 172.101:
DOT DESCRIPTION: Consumer Commodity ORM-D

SECTION XV - REGULATORY INFORMATION
U.S. Federal Regulations:
TSCA – Intentional ingredients are listed; CERCLA RQ-40CFR 302.4 (a) – None listed; SARA 302 Components 40 CFR 355 Appendix A – None; Section 311/312 Hazard Class-40CFR 370.2 – Immediate ( )
Delayed ( ) Fire ( ) Reactive ( ) Sudden release of pressure ( ); SARA 313 Components 40CFR 372.65 – None; OSHA Process Safety Management 29CFR1910 – None listed; EPA Accidental Release Prevention
40CFR68 – None listed.
International Regulations:
ACOIN (Australia), DSL (Canada), ECL (South Korea), & EINECS (Europe) – Intentional ingredients are listed.
State & Local Regulations:
California Prop 65 - None

SECTION XVI - OTHER INFORMATION
Refer to product label for directions and any other cautions.
LEGEND: ND, Not Determined; N/A Not Applicable; NA, Not Available.
NOTICE
All information appearing herein is based upon data obtained from chemical manufacturers and or recognized technical sources. While the information is believed to be accurate, Snyder Manufacturing Corporation
makes no representations as to its accuracy or sufficiency. Conditions of use are beyond Snyder Manufacturing Corporationʼs control and therefore users are responsible for and assume all risks of their use, handling,
and disposal of the product, or from the publication or use of, or reliance upon, information contained herein. This information relates only to the product designated herein, and does not relate to its use in combination
with any other material or in any other process.