THIS PRODUCT IS VOC COMPLIANT AND LEGAL FOR USE IN ALL 50 STATES
Stone Pro High Gloss
Sealer is a high density acrylic that adds color, brilliance and gloss
to porous stone, rock, Saltillo, pavers, slate, limestone, travertine,
and masonry. It provides outstanding protection against water
and oil-based stains and acid damage.
Stone Pro High Gloss
Sealer can be used in both interior and exterior applications, is UV resistant, and won't peel, crack, or yellow. It is easy to use, dries in about half the time of conventional acrylics, and produces beautiful results - every time!
Coverage: Product will cover approximately 200 to 1,000 ft.˛ per gallon dependant on the porosity of the surface. For highest gloss, additional coats may be required. Directions: - Test product in an inconspicuous area to ensure suitability for intended use.
- Ensure the surface is clean, dry, thoroughly swept, and free of any previous wax or sealant contaminants. For best results, use Stone Pro Formula 51 Stripper to remove any previous wax or acrylic coatings.
- Apply Stone Gloss using a lamb’s wool applicator, roller, low pressure sprayer, airless sprayer, or string mop. Apply consistently.
- Let dry for at least one hour between coats.
- Surface may be opened to foot traffic after 24 hours; full cure is achieved after 7 days.
SECTION I - PRODUCT IDENTIFICATION
TRADE NAME: Stone Pro Stone Gloss PRODUCT CODE: SPSG
CHEMICAL NAME: Acrylic blend CAS #: Blend, no single CAS # applies DOT HAZARD CLASS: Not regulated DATE: February 19, 2005
DOT SHIPPING NAME: Not regulated
SECTION II - HAZARDOUS INGREDIENTS
HAZARDOUS INGREDIENTS % CAS # TLV (UNITS) PEL
2(butyoxyethoxy) Ethanol <5 112345 None None
SECTION III - PHYSICAL DATA
BOILING POINT: (F) 212 SOLUBILITY: Complete pH: 7.5-9.0
VOC: 30 g/L VAPOR DENSITY: N/A VAPOR PRESSURE: N/A
EVAPORATION RATE (WATER = 1); >1 SPECIFIC GRAVITY: 1.025
APPEARANCE & ODOR: Opaque white liquid with a solvent odor.
SECTION IV - FIRE AND EXPLOSION HAZARD INFORMATION
FLASH POINT: N/A
FLAMMABLE LIMITS: N/A LOWER: N/A UPPER: N/A
FIRE/EXPLOSION HAZARDS: None
EXTINGUISHING MEDIA: Foam, CO2, dry chemical
FIRE FIGHTING PROCEDURES: Fire fighters should wear self-contained breathing apparatus and full protective clothing. Use water spray to cool nearby containers and structures exposed to fire.
SECTION V - HEALTH HAZARD INFORMATION
PERMISSIBLE EXPOSURE LEVEL: ND
EYES: Will cause irritation and redness.
SKIN: Prolonged contact will cause slight irritation.
INHALATION: Prolonged inhalation of mist may cause respiratory irritation.
INGESTION: May cause gastrointestinal irritation.
THIS MATERIAL IS NOT LISTED AS A CARCINOGEN BY IARC, NTP OR OSHA
HMIS HAZARD CLASS: Health = 1 Flammability = 0 Reactivity = 0 Other =NA
Ranking: 0 = Least 1 = Slight 2 = Moderate 3 = High 4 = Extreme
FIRST AID
EYE CONTACT: Flush with water for 15 minutes lifting eyelids. Get medical attention immediately
SKIN CONTACT: Wash with water and treat with any moisturizing cream.
INHALATION: Remove victim to fresh air. Administer artificial respiration if breathing ceases. Get medical attention immediately.
INGESTION: Do not induce vomiting. Give lots of water. Give milk of magnesia. Call a physician.
SECTION VI - REACTIVITY INFORMATION
STABILITY: Stable
REACTIVITY: None will occur
HAZARDOUS DECOMPOSITION INGREDIENTS: N/A
HAZARDOUS POLYMERIZATION: Will not occur
SECTION VII - SPILL, LEAK AND DISPOSAL PROCEDURES
SMALL SPILLS: Mop, sweep or absorb. Transport to non-hazardous land fill.
LARGE SPILLS: Mop, sweep, or absorb. Transport to non-hazardous land fill.
DISPOSAL: Dispose of in accordance with federal, state, and local regulations.
SECTION VIII - SPECIAL PROTECTIVE EQUIPMENT
EYE AND FACIAL: Wear chemical splash goggles.
SKIN: Vinyl, rubber, or nitrile gloves should be used.
RESPIRATORY: Provide OSHA approved mists respirator.
VENTILATION: Local mechanical ventilation to keep TLVʼS below recommended levels.
OTHER: Wear protective apron, boots, and clothing.
SECTION IX - SPECIAL PRECAUTIONS
STORAGE: Store in cool dry well ventilated place
HANDLING: Avoid strong mineral acids.
LEGEND: ND, Not Determined; N/A Not Applicable; NA, Not Available.
NOTICE
All information appearing herein is based upon data obtained from chemical manufacturers and or recognized technical sources. While the information is believed to be accurate, Snyder Manufacturing Corporation makes no representations as to its accuracy or sufficiency. Conditions of use are beyond Snyder Manufacturing Corporationʼs control and therefore users are responsible for and assume all risks of their use, handling, and disposal of the product, or from the publication or use of, or reliance upon, information contained herein. This information relates only to the product designated herein, and does not relate to its use in combination with any other material or in any other process
|
