Stone Pro Color Enhancer is a unique, V.O.C. compliant product designed to naturally enhance the colors of honed, polished, flamed, hammered, and sand blasted natural stones, bricks, pavers and masonry. It is gas permeable (allows the surface to "breathe", ensuring harmful moisture and other substances are not trapped beneath the surface) and will not "yellow" or otherwise discolor with age.
This product provides some hydrophobic (water) sealing properties, and does not provide protection against oil-based stains. To achieve complete water and oil repellancy, the surface should be treated with one coat of Stone Pro Porous Pro Impregnator after Stone Pro Color Enhancer is applied.
Coverage: Product will cover approximately 200 to 1,000 ft.˛ per gallon dependant on the porosity of the surface. Two coats
are recommended to independantly achieve maximum water repellancy; color enhancement is usually achieved with a single coat. Allow minimum of 24 hours between coats; full cure is achieved in 72 hours.
Directions:
Always test product in an inconspicuous area to test suitability for intended use.
Surface must be sound, thoroughly clean, and free from waxes, sealants, or coatings of any kind. For best results, use Stone Pro Deep Clean Gel to remove soil and embedded dirt, or Formula 51 Stripper to remove waxes or topical coatings before applying Color Enhancer.
Apply product evenly using a low-pressure sprayer or lamb's wool applicator. Do not dilute in any way. Please wipe off any excess residue after applying each coat. Excess residue may become slippery. If complete hydrophobic (water) and/or oleophobic (oil) protection is required, apply a coat of Stone Pro Porous Pro Impregnator after the application of Stone Pro Color Enhancer
Caution: Combustible. Keep away from heat, open flame, sparks and/or any possible ignition source. Keep work area well ventilated. Gloves and goggles should be worn at all times. Respirator suggested in larger areas or non-ventilated areas. Read directions and other cautions on back of container before use of this product.
Color Enhancer SECTION I -COMPANY &PRODUCT IDENTIFICATION
TRADE NAME:Stone Pro Color Enhancer/Sealer
PRODUCT CODE:N/A
CHEMICAL NAME:Hydrocarbon blend CAS #:Mixture,no single CAS #applies
DATE:September 5,2003
SECTION II -COMPOSITION FORMULA -HAZARDOUS INGREDIENTS
HAZARDOUS INGREDIENTS %CAS #TLV (UNITS)PEL
Aliphatic Petroleum Distilates <50 64742-88-7 100 ppm 100 ppm
SECTION III -HAZARDS IDENTIFICATION
PERMISSIBLE EXPOSURE LEVEL:Undetermined
EYES:May cause mild eye irritation.
SKIN:May cause mild skin irritation.
INHALATION:Breathing small amounts of this material during normal handling is not likely to cause harmful effects.
INGESTION:Swallowing small amounts of this material during normal handling is not likely to cause harmful effects.
THIS MATERIAL IS NOT LISTED AS A CARCINOGEN BY IARC,NTP OR OSHA
SECTION IV -FIRST AID MEASURES
EYE CONTACT:Flush with water for 15 minutes lifting eyelids.Get medical attention.
SKIN CONTACT:Immediately flush skin with water for 15 minutes.Remove and launder contaminated clothing be-
fore use.
INHALATION:Remove victim to fresh air.Administer arti ficial respiration if breathing ceases.Get medical attention
immediately.
INGESTION:Do not induce vomiting.Call physician or transport to an emergency medical facility.
SECTION V -FIRE AND EXPLOSION HAZARD INFORMATION
FLASH POINT:142 – 150 deg..F.
EXPLOSIVE LIMITS:LOWER:1.0 UPPER:6.0
FIRE/EXPLOSION HAZARDS:Vapors are heavier than air and may travel along the ground or be moved by air and
ventilation and ignited at a distant source.
EXTINGUISHING MEDIA:Foam,CO2,dry chemical
FIRE FIGHTING PROCEDURES:Fire fighters should wear self-contained breathing apparatus with a full-face piece
operated in the positive pressure demand mode and full protective clothing.Use water spray to cool nearby con-
tainers and structures.
HMIS HAZARD CLASS:Health =1 Flammability =2 Reactivity =0 Other =NA
Ranking:0 =Least 1 =Slight 2 =Moderate 3 =High 4 =Extreme
SECTION VI -ACCIDENTAL RELEASE PROCEDURES
SMALL SPILLS:Absorb liquid on vermiculite,floor absorbent or other absorbent material.
LARGE SPILLS:Eliminate all ignition sources.Prevent run off to drains or any bodies of water.Pump or vacuum ma-
terial to containers for recovery.Absorb remaining material.
|
